home Fix label Kitchen Appliances label_important Dishwashers category Ignis

IGNIS dishwasher model ADL 347/2?

The start button light is flashing and the each time I try to use it the warning signal sounds and the program selects prewash but no water appears to enter. The last time I used the machine more or less successfully it sounded noisy.

D W Bird, January 2008

home Fix label Kitchen Appliances label_important Dishwashers category Ignisdone

there is a seal in the roof of the dishwasher that has perishes due to age/heat ,but i cannot find a description of one to order. (its the larger one of the 2)

rob, November 2017

My Ignis dishwasher will not empty the water to enable cycle to carry on what should I do ?

Sandi, January 2015

how do i change the lower door seal on an ignus adl347 intagrated dish washer,can i remove the inner door where the powder dispenser is mounted and then fit the seal or do i need to remove the unit from it`s built in postion

Mark f, February 2013

my dishwasher is not draining

Andy, October 2012

There is no power going to the dishwasher. I've changed the fuse and checked the wires and everything seems fine but its still not working? There was also water left in in the sump?

paul, August 2012

my ignis door is creaking sounds lick the spring has gon poss can i repair it myself model adl 347

chris, February 2012

Hi. My dishwasher is really leaking from underneath. Lots of water seeping out. Can't seem to figure out where from?

Fatemah, February 2012

all what every one has said on this page works ive just cleaned the arms on mine put them back on and i can still hear it working now lol

tuks, June 2011

my ignis dishwasher only works for the final phase does not start the wash cycle

gary clement, May 2011

Boiling water also helped with the blockage in my dishawashe - ADL 347/2.

Maxhouse, May 2011

dishwasher keeps flashing.. could you tell me whats wrong ?

carna hague, December 2010

Had a problem yesterday where my one year old machine just stopped mid cycle and was not filling with water or cleaning as expected. I simply took off the top and bottom plastic rotor arms " turn anti clockwise to click off" washed them in the sink and removed any food that had jemmed in the water holes. I then put the arms back in place turning clockwise until they click on and hey presto the machine is workin fine and cleaning the dishes as it shiould do.

Swifty, July 2010

how do i get the door of my dishwasher,so i can change the seal

haddow, March 2010

mine was making the same noise we also took the arms off and soaked them due to them being blocked and dirty! also put boiling water down the filter inside! put it on the hotest wash without the spray arms and its now working!!! thank god!

CLAIR, March 2010

Barry mac, February 2010

ou r dish washer model no adl 349/2 has stopped heating up. this is a new flat and the dish washer is only 1 year old. it is still under guarantee .

brian smith, December 2009

Hey I had the same problem with an IGNIS dishwasher model ADL 349/a with any cycle stopping after a few minutes with three short beeps and one long beep.

I took out the filter, cleaned it, poured in a kettle of boiling water and turned on the hottest wash and hey presto it worked!

Mark Bowman, November 2009

I had the same problem as above. the water was entering and then it wasn't making the splashing sound and then it entered and the finished alarm sounded. Turns out the filter had become loose so all the food that was in the bottom of the dishwasher (rice and peanuts) had been sucked up and had jammed the rotary arms meaning the water couldn't get through. The rotary arms twist off and then i had to pick all the food out with a pin!!!

Shellie, August 2009

I have same machine and while its getting water into it it does not have 'splashing' water when I open the door quickly. Is this the pump?

mike, July 2009

my dishwasher has stopped washing the dishes propably, can you help?

tammy blaikie, April 2009

Hi
It sounds like the pump is jammed. To unjam the pump looks hard but is easy when you know how. Just remove the 4 torque screws on the front bottom of the dishwasher, you will need to remove the kitchen plinth to access this, the dishwasher does not need to be removered for this. Inside at the front you will see a pink and white plastic pump. The pump front unscrews anticlockwise. A small plastic tongue has to be bent slightly to unscrew. remove the obstruction and all should be ok.
Cheers
Jocky

jocky, February 2008

i too have the same problem !!! The machine has been given 2 me second hand and having plumbed it it is giving the same fault !!!
I know water is entering because its in the botton sump !!

Rob, February 2008

link Click here to see other fixes for Ignis.