The motor works, the liquidizer works, the belt from the motor drive to the gear box is working but there is no drive for the beater.

P. J. Tunnard, April 2008

The machine was juddering but no / little movement and it could be held still by hand. I have replaced the brushes but the motor only comes on at slow speed and can still be held still by hand. Any dead, please?

Martin, June 2020

Can I replace the plastic blender drive on my A701A Kenwood chef

J.D.Gregory, August 2014

when we start the machine the nut come undone and falls off

geoff north, August 2012

contact kenwoodchefusedmixersansspares. 07507400101.
for all kenwood a701/ a901/kms etc. courier service provided. mick

mick, May 2012

Removing the dog clutch was a problem: (I had to swap a dog clutch and toothed drive wheel between two machines.) The thread on the dog clutch is in the usual direction so unscrew it anticlockwise, but only after immobilising the gearbox. I put a clamp on the main paddle drive D section shaft and turned till it jammed on the casing. You can also take the box off, do the same thing and clamp it all in a vice.

Spotty, October 2011

hi, just opened up my A701A gearbox and found that the small nylon cog on input shaft was split so wasn't gripping on the shaft so wasn't turning the cogs.

david, March 2010

The small clutch can wear on the 701 and 707 series, specifically there are 2 small lugs on each component which can wear down. The system was designed so that the slow speed outlets would be diconnected when the liquidiser or other high speed attachments were fitted. It's omitted on later models from the 901 onwards I suspect largely because it was a weak spot and not really necessary.

There is a way of over-riding a damaged component. Open up the gearbox and unscrew the drive shaft with the small clutch device on it. There is a spring on the outside of the casing which separates the clutch when the liquidiser cover is off. Reverse the spring so that it is on the inside of the gearbox and screw the clutch device together so its pulled down toward the gearbox and becomes permamently engaged. I've done this on 2 machines and they have worked perfectly ever since. Of course the planet hub etc will now rotate permamantly whether or not the liquidiser cover is fitted so rememeber not to leave any loose atachments in the bowl if you are using the high speed outlet!

John Glaholm, July 2009

Thought that I would let you know got the clutch dog only £4.50 (no usable pinion shafts available) fitted the same and all is working again, for another 30 years??
Regards
Maurice

Maurice, May 2008

Hi there, if you need your Kenwood mixer repaired or updated, there is a company in Montreal that repairs the mixers in 2 days with full guarantees, etc. They get mixers shipped to them from across the world. www.kenwoodservice.com

Tell them Annette sent you!

Annette, May 2008

Hi

I have a machine with the same problem Model No A701A Ser No A2376417.
I believe that I have found the answer .

If you remove the top cover (as you have already ) and view the nylon drive wheels and drive belt you will find that the larger (driven) wheel has an alloy “dog clutch” with copper coloured spring underneath it. This alloy retainer is threaded to the upper part of a pinion gear which goes into the gearbox. I believe that you will find that the thread of this alloy retainer is stripped. Kenwood no longer supply these parts. I have just spoken to Master spares on 023 8084 4338 who can supply pinion shaft gear and retaining alloy dog clutch (USED) for £11.95.. I guess that it would be best to fit all parts (will involve stripping out gearbox) or you may be lucky and if tread on existing steel pinion shaft is good , only fit alloy bit (can be fitted with out strip out of gearbox)

Good luck

Maurice

Maurice, May 2008