I've had my Hotpoint WD440 (Aquarius not Aquarius+) washer/dryer for 3 months, and when I switched it on yesterday, the On/Off lights flashed, along with the lights on the "Drying High Heat" and the "Creases" buttons. These lights continue flashing until I switch it off, but the machine won't do anything. Please help!

Alison, April 2007

Got it working.
I'm using a fast wash programme K, which is a cold wash. I have not tried any of the other programme with a No Heat setting, it might work for a longer wash?
It looks like it might have something to do with the temperature setting. It can be used until you get it fixed.

Jane, November 2012

hi there i have a bekko washer and the timesaver button keeps flashing and cant get another program

beverley, January 2012

error code 13, is what i have what does dryer ntc mean please

kim, October 2010

Hi I dont know if this will help by my WD440 displayed flashing:-on/off, Drying high heat, Reduce Creases and time saver lights.

Cleaned out lower filter at rear of drum which was not really soiled. Still lights flashing

removed pressure switch at back of powder drawer and the clear tube along with the larger white tube near lower filter, found minor debris in white tube. Clear tube ok and no blockage, blew into pressure switch to check function and seemed ok but may have been jammed open circuit prior to me blowing, checked switch function with multimeter and seemed to require a fair blow to get to register closed circuit so adjusted screw on front of switch to reduce required pressure, refitted offending switch and voila all now ok

Mark Gilbert, November 2009

i believe this means that the filter is blocked - just got the same problem myself. you need to take the back off of the machine and remove the water pipe to get to the filter though

lisa, April 2007

hi alison these are the light flashes

These codes are reading from the top neon down.

F01....OFF, OFF, OFF, Flash, OFF.
F02....OFF, OFF, Flash, OFF, OFF.
F03....OFF, OFF, Flash, Flash, OFF.
F04....OFF, Flash, OFF, OFF, OFF.
F05....OFF, Flash, OFF, Flash, OFF.
F06....OFF, Flash, Flash, OFF, OFF.
F07....OFF, Flash, Flash, Flash, OFF.
F08....Flash, OFF, OFF, OFF, OFF.
F09....Flash, OFF, OFF, Flash, OFF.
F10....Flash, OFF, Flash, OFF, OFF.
F11....Flash, OFF, Flash, Flash, OFF.
F12....Flash, Flash, OFF, OFF, OFF.
F13....Flash, Flash, OFF, Flash, OFF.
F14....Flash, Flash, Flash, OFF, OFF.
F15....Flash, Flash, Flash, Flash, OFF.
f16....OFF, OFF, OFF, OFF, Flash.
F17....OFF, OFF, OFF, Flash, Flash.
F18....OFF, OFF, ON, OFF, OFF. Fault on control board, check Eeprom.

Faults without error codes. If the motor is O/C the machine will not fill or operate.

The digital display models will generate the actual fault code, ie; F01 etc.

and this is what they mean

widl codes - light flashing from left to right are numbers 1-4

f01 light 4, motor triac
f02 light 3 motor, jammed/ tacho
f03 lights 3&4 Ntc fault
f04 light 2. pressure sw stuck on empty
f05 lights 2&4, pressure sw stuck on full
f06 lights 2&3, N/A?
f07 lights 2&3&4 heater relay
f08 light 1. heater relay
f09 lights 1&4 eprom/setup error
f10 lights 1&3, pressure switch not sensing
f11 lights 1&3&4, pump/draining error
f12 lights 1&2, communication error
f13 lights 1&2&4, dryer ntc/ fan motor
f14 lights 1&2&3, dryer heater
f15 lights 1&2&3&4, dryer heater relay
f16 N/A
f17 light 4, door lock
f18 light 3 comms error (3 phase motor) power board

f1 and f17 share the same light

Anymore questions http://www.freewebs.com/msdapudsey1
Just go to the forum

phil grimshaw, April 2007