GG asked ... Fix food processor motor?    |    T asked ... How do I turn the delay off on Electrolux DX302 dishwasher?    |    Helen asked ... How can I mend my Kenwood Gourmet FP505?    |    Roy Turner asked ... Kohlangaz Gosford HE fire?    |    Peter asked ... How can I mend a Powerwasher PRO PRO1800PWE?    |    Click here to ask your question

how do i reprograme my cobra 7777 keyfob?

i recently changed my battery in my fob and instead of the light flashing it just stays lit when holding any button. it will not arm or disarm the alarm or open the doors. could you help?
peter, October 2007
Hi where is the "little black box " located please

Riobey, March 2016
Goto http://cobracartech.co.uk/accessories-/147-key-fob-replacement.html and click the download tab there's a PDF there

Michael Mc, February 2014
As instructed by my Mitsubishi garage. Switch ignition on; press both buttons together until light stops flashing; press small button twice not too rapidly and that should be that.

Nick, October 2013
just use patience and read the above steps. it took me three turns to get both my fobs programmed.
thanks guys

Rafi, August 2013
Hey guys, I had lost both my keys and nothing worked here is what i did.
1) ignition off
2)I had dip switch 3 in the control box on, I turned this off and turned dip switch 2 on.
3)held down both buttons at once till the light stopped flashing, then pressed right button then left.
4)set dip switch 2 off and switch 3 on again and hey presto it worked. Hope my trial and error can help you.

Jack, May 2013
iv tryed all above un still no luck can anyone help

mark h, April 2013
You don't need to insert your key into ignition. Just leave the fob without the battery for 2 mins, (put the battery now) hold 2 buttons for 10-12 secs and then click the big one two times. I have just reprogrammed 2 fobs for Galant using this method.

Zielu, September 2012
had the same problem of the light not turning off when i pressed the two buttons.
wait 2 min and make sure when you put the new batt in that the light is lit up solid red. then press and hold the buttons , light will blink so wait until it stops.
then press the big button twice for a second each time.
each time the light will blink then stop. and the door should unlock.
this worked for me. hope it helps. i know how frustrating it is now.

rudygon, October 2011
i have done what it said on here above and nothing is working on my cobra 7777. it will not lock or unlock the doors. please could someone help thanx

steven drawbridge, July 2011
Worked perfect for my 2005 Shogun 3.2D, although I did have the key in the ignition.

(1) open up your keyfob and remove the battery for around 2 mins.

(2) - insert new battery (if needed). The red-light stays on all the time

(3) - go to the car (I now put the key into the ignition and turned to when the electric came on) and press the big button twice. This only took about 10 seconds, but may differ.

(4) - the red-light goes out and this has now synchronised the fob to the alarm.

Thanks,

Kev

Kev, July 2010
With alarm set...press both buttons until red led goes out..release both buttons..press left button (big one) twice. Done!

Fivish, March 2010
I'm in Portugal and my Keyfob Alarm is a 7777-06 and for me worked like Steve Brown says:

"I phoned Cobra in the UK and this answer solved my problem. Apparently, it needed synchronising again:

(1) open up your keyfob and remove the battery for around 2 mins.

(2) - insert new battery. The red-light stays on all the time

(3) - go to the car and press the big button twice.

(4) - the red-light goes out and this has now synchronised the fob to the alarm.

(NOTE) If you want to get to stage 2 without re-inserting the battery, press and hold BOTH buttons for a while until the light comes on.

Steve Brown June 2008 "

Thanks to Steve Brown

PTAlarm, February 2010
blown a fuse earlier on n it surged power through my car blowing my side lamps n naffin my alarm up :S when i activate my alarm instead of two beeps it makes 6 and when de avtivating it makes 4 or 5 :S any 1 know why????

crock, September 2009
Hy guys Here is the solution !!!
I've tried the other solutions with no luck but this 1 did the trick !!!

1. open up the key fob and remove the battery for 2 mins.

2. Insert new battery. The red-light stays on all the time.

3. Press Both of the Buttons - the light will start blinking

4. When the blinking light stops- stop pressing the right button and then the left one.

5. Try to use the key fob.

6. If it doesn't work repeat steps 3-4 again until it finds the right frequency.

Good Luck!

TgM, September 2009
i have an intermittant problem with my cobra 7777 Alarm, ive replaced the door pins as the dash said that the two front doors were always open, this problem has now gone, but the key fob plays up still, the alarm goes off rather alot, and wont stop, i often find the car has been unlocked overnight, i think i need to retune/re-syncronise the alarm? anyone with any ideas on how to go about this would be appreciated, i also have a honda accord alarm on the car that has not been disarmed??

Toni Marsh, August 2009
My 7777 remote is bad,i had to throw it away.I bought a second hand one from e bay, without battery. What do i have to do to make it work with my car alarm, do i have to program and/or synchronise? Thanks

Sandro, January 2009
Gill thanks everithimgs working

kommando1@hotmail.com, October 2008
I confirm the answer by Steve Brown from June 2008 works - just saved me serious problems! Thanks

Gill, September 2008
I phoned Cobra in the UK and this answer solved my problem. Apparently, it needed synchronising again:

(1) open up your keyfob and remove the battery for around 2 mins.

(2) - insert new battery. The red-light stays on all the time

(3) - go to the car and press the big button twice.

(4) - the red-light goes out and this has now synchronised the fob to the alarm.

(NOTE) If you want to get to stage 2 without re-inserting the battery, press and hold BOTH buttons for a while until the light comes on.

Steve Brown, June 2008
Solved.
Remove the new battery, wait 2-3 minutes, press the buttons a few times.
Put the battery back. Now, the LED stays lit, without pressing any buttons. If you wait, or press one of them, the LED will go out, and we're ready.

iscsu, October 2007
I have the same problem (tried with 2 different (E.....zer, D....ell) CR2032 batteries).

Anyway, to answer the question:
The re-coding procedure:
Open the centralized command with the remote control. Do not turn on the ignition.
Set DIP SWITCH N° 2 to the > ON < position on the part N° 000 054 640 (the little black box).
Press the two buttons on one of the transmitters (either can be used) until its LED goes out. Release the keys. The LED will remain on. Now briefly press the bigger key. The LED will come on for about 1 sec.

The problem is that with the new battery, the LED won't go out, no matter how long i press the two button...
Anybody?

iscsu, October 2007