can you give me the code to reset my beko wma1715 washing machine as it is just flashing on prewash thank you

Tanya, April 2005

HI
The door on my beko wma 1751s wont open no green light on on it.

Claire, November 2016

Can anyone help??
My Beko WM51502 start/pause button not working and not lit up. All the other buttons work, just cannot start the thing. I have tried resetting, but of course if the start button is not on resetting might be a problem.

Has anyone had similar or same problem, can anyone help.

Thanks

Jane, April 2016

Just to add, I have a Beko WMB series machine and the reset sequence is slightly different as you don't set it to 90c but rather to Cottons (12 o'clock on the dial).
Also after holding Start/Cancel for 10s I got a code - 0427 - then all the icons on the display light up. I then pressed start once and turned off and on again.
Display was still flashing 00:00 and not responding (which is the original error condition that started all this for me)
I turned the programme dial from Cottons to the programme it was on when it started to go wrong. And closed the door. It then displayed "End" and locked the door, and went through the cycle you get when you cancel a programme, e.g. locked for 3 mins.
After that all was working!
HTH someone with a slightly different machine

Jed, February 2016

Great! Thanks a lot!

Leo, August 2014

Worked wonders for us.. followed the reset for our wmb 81445 washing machine. Reset allowed us to get the lock off. Then drained manually, took out load, found hair clip stuck in the little motor in the filter pump. Took out with long plyers.. all working fine now 😃

benster2004, May 2014

This thread made me very happy.

I have just fixed my Crystal MH 665 washing machine using the same code as was given here for the Beko one. Saved myself a lot of money and having to miss work waiting for the repair guy.

Plus it allowed me to give my kids a demonstration of how Moms can fix washing machines too.

Hagar, May 2014

Thanks so much, this worked perfectly, and my boyfriends very proud of me :)

Amyz, March 2014

Fantastic the reset instructions worked and have released machine to spin. You are a genius

Sally, March 2014

Fixed mine too by removing a piece of material that had jammed the pump found behind the small door at the bottom of the machine. Get ready for any water in the machine to drain out (a lot) and turn the filter clockwise to remove. Don't just check the filter which is on the back of the piece you've just removed, almost LOOK UP THE PIPE into the machine. The pump is just a few inches in and can get obstructed. Remove any thing you see that should be there and gently rotate the pump to check that it moves smoothly. Replace the filter turning it anti-clockwise. Then rest you machine as in the posts below and you should find your machine works.

This is a common problem with beco's.

Miles A, February 2014

How can I reset my beko WML 15080 Y ? It's not spinning during the normal wash and when I select spin mode it's only spin for a short time and that's it. Thanks

Fcb078, December 2013

Wow this worked :-) A hairgrip was the culprit in this case, jammed in the outlet pump :-(

On my machine a Beko WM 71641, you set it to cottons, at the 12 O'clock position.

A bit of advice, turn the machine off first, wait for the click of the door unlocking, empty the wet laundry into a bucket, then bail out the drum of the machine (I used a takeaway container) into another bucket, then follow the instructions in the other posts about re-setting the machine and cleaning the filter. Emptying the machine first saves mopping 4+ litres of water off your kitchen floor when you open the filter - have sponges and shamwow cloths handy..

Firestarter, December 2013

hi i have tried this three times but it wont work for me my beko is wm5140w it spins and fills a bit with water but wont wash is tries to work and sounds a bit like a humming noise and then thats it any ideas please? i have checked filter nothin stuck in it all clear thank u

JANE BORDEN, September 2013

is it the same for the beko wm72cpw washing machine??? help

stev, September 2013

That's fantastic as it worked for my Beko wma 1512 w.

Many thanks

Thun Thun Gopal, August 2013

Hi I have a Beko 1200rpm WME8227B that's on pause no matter which cycle I put it on. I've drained the filter and still no luck. Can anyone help !!

sam, April 2013

i have been on the verge of having to ring repair man til I found this site and washing machine is now working again!! amazing!!

Louise, December 2012

I did the same, reset washer, had to drain first soggy wet washing and me, cleared the filter and now it works again. Thank you so much for the solution it has saved me a lot of money right on xmas time.

Diane, December 2012

Great instruction, it worked !!

Guest, October 2012

guys, my washing machine BEKO WM512S ended up not spin or drain, with clothes in, i done what it said on here from great clever guy: Big thanks to all for usefull posts.With your sugestions i reset my Beko SWM 3508 TGK washing machine.
Procedure for reset:
-Turn Off power switch
-Select 90 degree washing
-Press and hold Start
-Turn ON power switch and keep pressed Start button 10 sec
-Depress Start button
-Turn Off power switch and turn On again and thats it...

it did finally let me to choose program, but still ended up not draining or spinning...after4 hours found manual, you should clean pump filter.
how to do it:

1.disconnect /unplug the machine from power supply, be careful if you did washing on 60 or 90'C, leave it to cool down for few hours first
2. open filter cap, it is under the door, you should hold it from both sides and open it by pulling out.
3.place large container in front of the filter to get water flowing from filter, get cloth and bucket as well, i had lots of water there.
4.loosen pump filter (white round thing)anticlockwise until water starts to flow out of it to container.
5.when there is no water left, turn pump filter until is completely loose and remove it.
6.now you can find all dirt and rubbish inside, so clean it all... and close the pump filter properly...plus filter cup just pushing on the sides.

guys i had piece of wire from underwear and this stupid colour catcher sheet, and thats why it stopped working. happy days, i saved myself £100 at last for xmas. good luck

Zuzana, October 2012

Looks like this works on the Beko wm5100 - it now works and has been re-set :-):
-Turn Off power switch
-Select 90 degree washing
-Press and hold Start
-Turn ON power switch and keep pressed Start button 10 sec
-Depress Start button
-Turn Off power switch and turn On again and thats it...

jon, June 2012

Wow it flippin well works! This was on WMC62W model - now completing a cycle after frustrating 3 hrs. Only difference is there is only one "START/CANCEL"button to hold in instead of 2. Thanks!

Jim and Sue Taylor, May 2012

not the same problem need help dont no wer to lookbeko wm5100w the drum on goin aound its not the belt

sharon, March 2012

Hi everyone.
Thank you so much for the answer. I think I overloaded my machine, so it just turned off keeping the door locked.

As I apply the code, the machine starts running through all the elements of the washing cycle.

I believe that when I held start again for three seconds it turned off.

What I then did was press start so it would turn on, and have it run only the draining program. That took like a minute, and then 'pop', door opened!

Thanks!

Evan, October 2011

Hello I have had the similar problem as many of you described.. however, it seems to have amind of its own atm and it will go through a whole wash cycle, then for some reason start filling up with with water again and then stop half way through.. therefore altho I can reset the machine, it wont do anything apart from spin.. which is no good when I have water still to drain.. any ideas about how to get it to drain without having to go through the manual way of draining ir which I have done before and takes forever :-(...

Linda, October 2011

er, not quite, update to below, i was too quick to say done. wm spins fine with no clothes, doesnt spin with a single pair of jeans, answer from other site --

This one is VERY common to more modern machines that are run by electronics (most machines of 6 years or less). This problem arises when you try to spin one item on its own ie: bath mat, dressing gown ect, you will find that all the water has gone but it has not spun, this is because all modern machines use electronics to run all programs and they measure the drum speed very accurately to stop it doing an unbalanced spin. If you ever have this problem simply open the door and put a large dry bath sheet in with the load and spin it again, you should find it now spins OK.

---

silver darling, September 2011

thanks all, Vedad Kezo, February 2011 answer worked for me. on my beko WM7335W the cancel and start button are the same thing.

i did check the filter tho' -- bit of advice from other site once you have filter off --
Look into the open pump housing to see if the pump impellor is spinning.

it was so i knew this wasn't problem and reset

silver darling, September 2011

hi i have a beko wm5120s, when i try starting a programme the pump works for a few seconds then the start/pause light flashes and the door unlocks! ive tried the reset but no change! any ideas?

ray, August 2011

anyone know why my quick wash button does not work on my beko wm5120w washing machine?

same as the pre wash button but the extra rinse button works.

anyone got any help many thanks

wayne hallett, July 2011

thank you very much for the reset steps, were now up and running

steve, July 2011

I am grateful to this web site and I also thank Martin and Vedad Kezo for providing these information(December,2010 and February,2011 respectively). It worked like a magic!

babatunde., June 2011

thankyou so much this jus worked 4 me imso happy lol

maria, May 2011

i have a beko wma510 can anyone tell me how to reset it the start/pause button are flashing and also the prewash button i tryed the above meatherd but did not work i had a blockage cleared it out and now this HELP

paul lyons, April 2011

I've just read out the reset instructions to my boyfriend because his washing machine was stuck on a cycle and he's now hopping around the kitchen woop wooping! He sounds delighted to have his washing machine working again! Happy Days! Thanks so much to Vedad and for this thread! 80)

AmandaMoo, February 2011

Big thanks to all for usefull posts.With your sugestions i reset my Beko SWM 3508 TGK washing machine.
Procedure for reset:
-Turn Off power switch
-Select 90 degree washing
-Press and hold Start
-Turn ON power switch and keep pressed Start button 10 sec
-Depress Start button
-Turn Off power switch and turn On again and thats it...

Vedad Kezo, February 2011

Wow - yes the answer I've re-pasted below does work!! It sure is funny that there are totally different instructions in the manual - and those don't work. Big thanks to whoever worked this out. It's happened the only couple of times before when I've tried to do a pre-wash and those times I just fiddled randomly until it eventually started up again - but couldn't get it going this time till I tried the below.

Have had the same problem, prewash light flashing right hand side of machine. The shop I purchased machine from have spoken to their Engineer and it's a case of re-setting the machine. Have told me how to do it and the machine's working again - fingers crossed!
Turn power button off (not at wall)
Select 90 degree wash
Press Start and Cancel button down at same time for 3 seconds and turn power button on whilst still holding buttons down - Start light will flash.
Leave power on.
Select any Spin position.
Press Start and Cancel button at same time again for 3 seconds - other buttons may start to flash - if they do, press Start and Cancel button together again for 3 seconds.
Machine should be re-set ready for use.

Martin, December 2010

Emily Plant's post worked like a charm. all the posts have helped, i've managed to clean the filter and reset the machine.....many thanks for some sound advice

Captain James, November 2010

i need help my washing machine will not work the ready and wash lights keep going on and off help me please someone many thanks

terry, August 2010

great stuff on the filter option - WMS5120 - take the filter out and get rid of the crud and the whole machine works again - I didnt bother resetting as this seemed to fix it no problem

moz, August 2010

was told to unplug machine for 2 hrs plug machine back in hold start pause button for 5 seconds and it is working again!!

diane, July 2010

Great advice. Thank you touch wood all working again

rachel, July 2010

i have a beko wma655w washing machine.have move house but it needs resetting,any ideas thanks

karen, March 2010

This worked with my BEKO WM 5120 W. The drum must be empty of water. Remove filter bottom right of washing machine, behind the kicker to empty water quickly. Requires two people and a bucket/ washing up bowl or lots of towels. Put filter cover back on. Wait 2 - 3 mins. Switch on as described below. Start/ cancel button on this model is one and the same. Job done.

Barney, February 2010

Had the same problem with ours after 18 months. Spent 3 days trying everything to reset it but nothing worked, then one last thought before taking it to the tip I checked the hose. These machines don't spin if there is water in the cylinder, so I disconnected the hose from the drain pipe, put it in a bucket and turned the machine back on and water flooded out. The blockage was at the rubber none return valve in our kitchen wastepipe. Two curtain hooks and a button later and everything was fine. Hope this helps

Mike, February 2010

i have tried all of these and still nothing is working!

julie, November 2009

that solution worked and many thanks

Jo, November 2009

hi room all the lights flash on my beko wma 510 s nothing happens any ideas many thanks in advance

lisa w, November 2009

My Beko WMA 1715s just has the door light on, and i have tried all the above methods to reset it, but none of them work. Does anyone know of anything else?

Thanks

Antony, September 2009

Hi.
I just finished a wash and now I only get a power light and the door open light.
nothing else lights up at all.
can this be fixed using buttons or do i need parts?

the cancel button & start button are the same button on this one. start/pause/cancel

thanks

Cathy, August 2009

hi,
my beko waher was flashing pre-wash, i did the whole 90 degree setting etc to restart the machine, now when i put it on a wash it PAUSES itself!!!!!!! cant get it to work.
PLEASE HELP
michelle.

michelle jordan, August 2009

wot a great solution, to rest your beko washer, just did it, it worked. many thanks
michelle

michelle jordan, August 2009

Hi, I just tried this solution is it was spot, give it try and will work
Turn power button off (not at wall)
Select 90 degree wash
Press Start and Cancel button down at same time for 3 seconds and turn power button on whilst still holding buttons down - Start light will flash.
Leave power on.
Select any Spin position.
Press Start and Cancel button at same time again for 3 seconds - other buttons may start to flash - if they do, press Start and Cancel button together again for 3 seconds.
Machine should be re-set ready for use.
Good luck!
All we need now is for the rain to stop!

Mawuto, March 2009

Help Please
We have a Beko WMA510W
It needs reset
The following lights are on the front panel start/pause wash and spin lights.
Can someone tell me how to reset the machine.
Thanks Stuart

Stuart Fraser, December 2008

hold in the start button for 7 seconds and everything goes back to normal

michelle mears, January 2008

WOW hats of to you !!! I fixed the motor and then had to reset it and work excellent !! wouldn't have been able to do it without the top tip thanks :O)

jon, July 2007

Emily Plant is an absolute star - its just worked on my washer. That will have saved call out charges - do manufacturers do this deliberately now as its such a good money spinner - lessons learnt fromthe car industry - dont give them a simple reset button so that they can sort themselves when there is money to be made! Thanks again Emily! xx

John Anderson, December 2006

Hi i wounder if you could help i have the same problem with my washing machine . I reset it using the above instructions and it sort of worked but now it with start a wash and then just pause and after a while go back to pre wash any ideas would be a great help .
thank you
emily

emily plant, June 2006

I had the same problem and found that someone had an answer on this site. i have cut and pasted it from the ladies answer. it worked for me. all the credit obviously goes to this lady and i am sure she wont mind what ive done. so have a go and hopefully it should work. ive even left her name on the bottom.

Have had the same problem, prewash light flashing right hand side of machine. The shop I purchased machine from have spoken to their Engineer and it's a case of re-setting the machine. Have told me how to do it and the machine's working again - fingers crossed!
Turn power button off (not at wall)
Select 90 degree wash
Press Start and Cancel button down at same time for 3 seconds and turn power button on whilst still holding buttons down - Start light will flash.
Leave power on.
Select any Spin position.
Press Start and Cancel button at same time again for 3 seconds - other buttons may start to flash - if they do, press Start and Cancel button together again for 3 seconds.
Machine should be re-set ready for use.
Good luck!
All we need now is for the rain to stop!

Julie Green

dave, May 2005