The top of the right door handle is loose. I know there are 2 screws that hold it to the door, but I how do I get to them to tighten the handle?

Steve, September 2007

Thank you for this advice! Although the screw that is attached to the handle ( the one u use a allen key on) came off my handle and was still attached to my fridge, this post here helped me. My handle was have off. From this I knew I could push up and the whole
hanlde would come off. From there I had to unscrew both screws to remove the backet off the fridge in order to get the Allen key screw off. My handle is back on good as new! My husband wil
Be surprised when he comes home to see i figured out how to fix this!! Thanks again!

Debbie, July 2014

Followed this thread to try to tighten my Freezer handle. For newer models DO NOT tap handle up - to remove push left, to reattach press face against Freezer and push left. Simple !

Kungfuchoirboy, June 2013

The above explanation does work very well, however, we had a bit of trouble pulling the handle up. We realized that there is a mechanism inside the handle that loosens over time and that is why the top of the handle eventually backs out. If you are having difficulty lifting the handle off the fix the problem, try the following: because the handle is loose, you can see behind the loose a handle a metal clip/tab. Place a flat screwdrive under the tab and push towards the door. The. Have and assistant lift up and the handle will come off. Then simply tighten the gold bolt that is loosened with an Allen key and slide the handle back on. If you want to see the workings of this handle, try popping off the good handle as an example.
Good luck. Ultimately this problem must arrive over time as this gold Bolt slowly backs out loosening the handle.

Mit, January 2013

Follow the directions here, and it works like a charm- thanks for the help!

Todd in Dallas, December 2012

After being told by the Sears repair guy that he would charge $65.00 to just show up and that most repairs cost $150.00, I got online and read this. No exaggeration - walked into the kitchen did what this guy said to do and in less than one minute had the handle back on the door!! Just saved $150.00. Thanks to the person that posted this!!

Dee, February 2012

Ours is a Kenmore 106.56362400 SxS and after spending a frustrating year where the top of the fridge handle became looser and looser with no obvious way to tighten it and service calls running close to $100, I just googled the problem and came across this site. Slide the handle up as per answer below and discovered the star screw on the top of the handle was loose, the brackets on the door were fine. Took less than 30 seconds to tighten the screw and remount the handle.

THANK YOU!!

Chris, January 2012

Worked like a charm!!!

DI, October 2011

Thanks. Worked great on mine!!!

Mike4, August 2011

Slide the handle up, it will come out, then you can tighten the srews

pete, January 2011

This worked perfectly on my KENMORE Model 106.56539400 (side by side refrig/freezer). Thanks to the poster for all of the help! Much appreciated.

Rick Rogers, June 2010

Followed the instructions above and fixed my door handle.

Thanks for the help

Pete

pete, May 2010

Genius. Thanks for the posting. Follow the directions above and this is the quickest repair ever.

AG, January 2010

Thanks for posting this!!!!! It helped so very much.

My handles on the 5 year old Kenmore side by side (106-54563300) were so loose that the top wiggled and the bottom finally came off.

After reading in this thread how to remove the handle and work the clips holding the fastening screw, I simply used an alan wrech to tighten the screws and reattched the door handle.

Worked like a charm!

AT, October 2009

Yes, hitting from the bottom pushes the handle up. The door mounts have a spring-like part that can be pressed back towards the door so the handle screw will pass over it easier. If the handle has pulled away from the door enough you can use a flat head screw driver to push this part back and lift the handle up and off. Tighten loose handle screw(s), position and slide snap handle onto the door. It should be flush now. See owner's manual for the style 2 handle removal picture.

JT Nov 2008, November 2008

tap hard! from bottom of handle. Handle moves up then off. Tighten screws. Tap handle back from top of handle.

DG, July 2008