How can I mend Scantronic 9751 Panel?

Scantronic 9751. 9941 Keypad: Amber Pulse Warning Triangle light Hi, after what I believe was a power cut, my panel went completely dead, I replaced the 12v battery for my 9751 Scantronic alarm as ... more

Scantronic 9751 Aux DC Fail keep blowing fuses?

Have replaced fuse twice. Blows straightaway when system reset. How can I identify what is causing the problem

done

I have a Scantronic 9751. Message "Lid Tamper" ?

Lid Tamper message alternating with "reset required". I have entered 4 digit rest code it displays but then says "Invalid Code". Can anyone help please as I cannot rest the alarm at all at the momen ... more

how to fix scantronic 9751 K01 Tamper reset?

hi guys, cant seem to reset my Scantronic 9751 system it keeps showing K01 Tamper reset no matter how many times i key in my code. the keypad was not tampered with or anything - the mains kept trippin ... more

done

Help please! Scantronic 9751 with 9930 - K01 reset required!?

Would be very grateful for some help. Alarm went off this morning - it does that when we have a temporary power cut which happens around here a couple of times a year m. I couldn't find the code, my " ... more

done

scantronic 9751?

what i can do if i forgot my code

done

9751 alarm with tamper fault?

Folks, I have inheritted an alarm system with the purchase of a new house. It's a Watson Alarm system but it's basically a Scantronic 9751 system with 9930 control panel - rebadged. The 9930 had ... more

done

gts?

Do you have any dusty scantronic's in your old stock that your throwing away? We don't install 9751's very hard to get them cheap over here in north ireland (I moved over here I don't have the acce ... more

done

Scantronic 9751 - faulty?

Some 5 months after installation the alarm rang 3 times overnight and the security code would not stop it. The engineer replaced the keypad. About 5 months later the same thing happened again and then ... more

done

Scantronic 9751?

I have an intermittent fault on the 9751. The alarm will ring when the system is not active and there is no way of stopping it without power the system down. The unit supplier will not exchange the un ... more

done

I have bought myself a scantronic 9751 ?

I dont understand how to connect a standard 6 wire cable from a detector to it

done

Scantronic 9751 RF Failure Back Door?

I changed the battery on the contacts at both the front and back door, zone 1 and zone 7 as I was getting a battery failure alarm. I am now getting a RF Failure on 215/back door. The amber light is on ... more

scanrtonic 9751 alarm sounder going off in cold weather ?

my scantronic 9751 alrm sounder is going off in extreme weather conditions help

done

reset my scantronic 9751 alarm system?

I have had to replace the battery on my scantronc 9751 alarm system and now it is asking for a reset after lid tamper does any one know how to do this or is there an engineers code available to reset ... more

done

How to reset an 9930 scantronic?

Dose anyone know how to reset an 9930 as I had to remove the panel cover due to decor, now its asking for a reset. It flashes up lid tamper with code 9751

done

Can I change the battery backup myself on Scantronic ?

MY panel downstairs is a 9751, unsure of what is upstairs, when i went to unscrew the alarm sounded, so now i have low battery & tamper warning plus alarm keeps sounding the warning. Is it possible to ... more

done

Scantronic 9751 Reset Needed?

Hi, I have a Scantronic 9751 fitted to the house. When decorating by a keypad panel i knocked it and rattled the case and the tamper triggored. I need to reset it. I cannot find the original installat ... more

done

tamper fault?

i disconnected my second control pad in the bedroom to move it, when ive wired it back up i keep getting a fault k02 tamper,ive checked the wiring and its all in order can anyone advise me because i j ... more

done