Zanussi FL 881 - can I tighten the drive belt?

With a full load of washing the drum does not rotate fully. I think the drive belt has stretched. Do I need to replace the belt or is there a tensioner that I can adjust the tension with? The wash ... more

done

Hopoint Acquarius - On/Off Button?

Recently received a Hotpoint Acquarius 1100 Washer Dryer WD61 - Plumbed it in however it wouldn't come on and had an electrician confirm there was power into it but couldn't understand why it was dead ... more

done

How do I fix my Hotpoint washing machine?

I was washing some pillows in my Hotpoint washer. It started to shake bad before I could get to it. I stopped the machine and rearranged the load and started it again. It seemed to be ok. It finis ... more

done

Hoover AC90 makes the noises but does nothing?

Goes through a full wash cycle but the drum does not turn, the belt is not broken. Any ideas (Hoover AC90 - a few years old)

done

how do i fix the drum bearings on my indesit w161?

my machine is very noisy when spinning althought the drum does not seem loose i have been told that it is the drum bearings and it will cost me about £90 to get it fixed am i being conned?

done

The timer knob on my indesit washer-dryer keeps clicking round?

The timer knob on my Indesit washer-dryer WD10 keeps clicking round and will not set the correct programme, it fills and pumps out at the same time as the dial clicks round

done

HOW DO I FIX MY HOTPOINT WASHING MACHINE ?

HOW DO YOU REPLACE THE BRUSHES IN A HOTPOINT WASHING MACHINE

done

Install belt to washing mashine?

How do I install new belt to Maytag washing machine

done

AEG Lavamat 6555 - F2 fault code, water not draining?

Can anyone offer me some help with an AEG washing machine; it seems that the water is not being drained. The machine stops with 8 minutes left on the cycle. The Start light and the third from top sp ... more

done

Whirlpool AWM 336 door not opening?

After the fuse blew in mid cycle, the door refuses to release the catch. I have tried to re-run the cycle, leave the power on for a while, off for a while & various other combinations. i don't think t ... more

done

How do I repair the rinse and spin cycle?

My Kenmore 90 series doesn't spin and make a lot of grinding like noise when its running

done

how difficult is it to chage bearings on a tricity bendix washing machine?

washing machine is very noisy on spin banging noise even on a small load belt came off ,which is now probably stretched,would you agree it is the bearings most probably and is it fixable by an amate ... more

done

Leaking water valve - Can't get back off washer?

I have a Whirlpool 110.82673810 washer. I took the screw off the back, and I took the top off the control panel, but I can't get the back cover to inspect the water valve and/or replace it. Is there ... more

done

Faulty Module? - Hotpoint WMT 03?

The machine is switching itself off on any program after a couple of minutes. We believe it is the module (Computer unit). As they are expensive to buy, with no guarantee of success, is it worth cha ... more

done

hotpoint ultima 1200?

what does the error mean.......E30....on hotpoint ultima 1200 and how do i fix it......

done

Zanussi 1100 won't do anything!?

I've got a Zanussi 1100 washing machine. The program lights all appear as per normal and the door locks etc but it just sits there doing nothing??

done

replacement front door?

looking for replacement front glass for Hotpoint washing machine Aquarius extra model number WMA46S

done

Hotpoint Aquarius 1100 water level?

My Hotpoint Aquarius 1100 (4 years old) doesn't seem to be getting the clothes clean just lately. I noticed that the water level in the drum during the wash cycle seems to be pretty low - the water ... more

done

Zanussi WDJ 1074 Drive motor not working - help!?

Hi Everything seems to work on the machine except the main drum motor. Could it be a switching problem or the motor brushes. (The motor is totally dead, would the brushes have worn out gradually ca ... more

done

Candy 1200 ES Drum Drop?

The drum on my Candy 1200 ES has dropped about an inch so that the door opening is now stretched slightly downward and the spin is very noisy. Has it been damaged by unbalanced loads?? There are 2 s ... more

done